株洲环保型计算机电缆素雅
低烟无卤电缆，是指不含卤素（F、Cl、Br、I、At）、不含铅镉铬汞等环境物质的胶料制成，燃烧时不会发出有毒烟雾的环保型电缆。
低烟无卤电缆基本概述:● 其中卤素指针为：所有卤素的值≦50PPM(根据法规PREN 14582)● 燃烧后产生卤化氢气体的含量<100PPM(根据法规EN5067-2-1)● 燃烧后产生的卤化氢气体溶于水后的PH值≧4.3(弱酸性) (根据法规EN-50267-2-2)● 产品在密闭容器中燃烧后透过一束光线其透光率≧60%(根据法规EN-50268-2)● Pb<90PPM，Cd、Cr6+、Hg、PBBs、PBDEs均小于5PPM
低烟低卤、低烟无卤阻燃电缆特点及用途：本产品适用于交流额定电压450/750V及以下的地铁、高层建筑、商场、剧院、发电站、化学工厂、城市广场及其他公用事业等对电缆阻燃特性要求高的场合。电缆的无卤低烟、低卤低烟特性，当火灾发生时，蔓延速度慢，烟浓度低，可见度高，有害气体释放量小，便于人员撤离。
ia-K2YVR本安型PE绝缘PVC护套二芯绞合屏蔽控制软电缆适用于要求柔软的场合。超五类4对多股绞合线屏蔽数据电缆，符合中华人民共和国行业标准YD/T，符合美国ANSI/TIA/EIA-568B.2标准，ISO/IEC11801标准，ULSubject444标准。
Identification and length marking: there is a sexual identification mark on the cable appearance, and the marking interval is not more than 1m.
燃烧气体的腐蚀性小，也避免了对仪器设备的损害，低卤、无卤的特性，使得电缆材料在耐老化和耐紫外线及其它辐照性能大大提高，从而延长电缆的使用寿命。3X2X7/0.43环保型计算机电缆
低烟无卤电缆使用特性：1.电缆额定电压UO/U:450/750V，交流聚烯烃UO/U为0.6/1KV2.电缆长期工作温度为：-20℃－90℃，-40℃－105℃3.推荐弯曲半径：无铠装电缆应不小于电缆外径的6倍，有铠装或铜带屏蔽结构的电缆应不小于电缆外径的12倍。
低烟无卤电缆主要技术指标：1.电缆应经受环境温度下工频电压试验3kV，5min不击穿2.电缆的透光率应符合下表电缆外径 D（mm）透光率（%）≥电缆外径 D（mm）透光率（%）≥D>40705<D≤105010<D≤4060D≥540 3.电缆的不延燃性（阻燃特性）:应通过GB12666.5-90中B类成束燃烧试验。单根电线电缆垂直燃烧试验应通过GB12666.2-90 4.卤酸气体释放量，符合IEC754-1
5.燃烧气体的PH值和导电率，符合IEC754-2 PH≥4.3 电导率≤10μS/mm。
PID调节是目前用得最广泛的过程控制手段，且变化多端。需要弄清楚原理，知道如何调节参数即可。良好的编程习惯变量命名，功能块命名，定时器命名，**遵循一定的原则，可读性好；熟悉软件的基本命令的使用；编写公共的程序块，比如阀门，电机的公用块等；合理分配主程序、子程序和定时中断程序等；合理分配数据块，定时器，计数器，存储器变量等，注意变量位置不能重叠。软件内部机理每个软件都各有不同，基本的东西应该都包括的：了解指令的累加器，状态字等内容。
自承式电缆屏蔽：用轧纹或不轧纹金属带纵包子缆芯包带之外，两边搭接。屏蔽带表面涂敷的塑料薄膜与护层粘接自承式电缆护套：黑色低密度聚乙烯。自承式电缆吊线：吊线为7股镀锌钢绞线，标称外径为6．3mm和4．75mm两种，其抗张强度分别不小于3000kg和1800kg，吊线用热塑性涂料涂敷，以防钢丝锈蚀。
Precautions for installation of power cables: keep 2m distance when the cable is installed in parallel with the thermal pipe, and 0.5m should be maintained when crossing. The cable shall be installed at a distance of 0.5m in parallel or across other pipelines. When the cable is directly buried and installed, the buried depth of 1-35kv cable is not less than 0.7m. When 10KV and below cables are installed in parallel, the net distance between them shall not be less than 0.1m and 10-35kv shall not be less than 0.25m. The distance of cross installation is not less than 0.5m. Cable laying temperature is not lower than 0 ℃, bending radius: multi-core cable or 15 (D + D), a single cable 20 or more (D + D), (D for cable diameter, D) for the conductor diameter. 6 kv and above cable joint: (1) installing a cable terminal head, must be stripped semiconductor electric shielding layer, operation shall not damage the insulation, should avoid mark uneven situation, when necessary use sand paper to grind; The shield end should be flat and the graphite layer (carbon particles) should be cleaned. (2) plastic cable end copper tape screened and armor must be good grounding, the short circuit also follow this principle, avoid unbalanced three-phase run ShiGang armoured end produce inductive electromotive force, and even "lighter" and accidents such as burning sheath. It is required to use my tinplate to braid copper wire for grounding lead. When connecting with the cable copper belt, it should be welded with chromium-iron tin. The shield of three-phase copper tape should be connected with ground wire respectively. Note that the shielded ground wire and steel armor ground wire should be separately drawn out and insulated from each other. The position of the welded ground wire should be as low as possible. Basic requirements for cable terminals and intermediate joints: a. good conductor connection; B. The insulation is reliable, and it is recommended to use irradiated cross-linked heat-shrinkable silicone rubber insulation materials; C. good sealing; D. sufficient mechanical strength to meet various operating conditions. The end of the cable must be used to prevent erosion of water and other corrosive materials, so as to prevent breakdown due to the aging of the insulation layer caused by water trees. Crane or forklift should be used for the loading and unloading of cables. It is forbidden to run flat or lay flat. For installation of large cables, cable laying cart should be used to avoid external damage or abrasion caused by manual dragging. If the cable cannot be laid in time for some reason, it should be stored in a dry place to prevent sunlight from exploding and water entering the end of the cable. Note: the installation of wire and cable should be done by the installation personnel or full-time technical personnel familiar with the performance of wire and cable. If there are still unclear matters, please consult the relevant technical department or the technical department of our factory.
充油电缆主要电气性能：1.充油电缆直流电阻:20℃,0.4≤1480.5 ≤95.00.6≤65.80.8≤36.62.充油电缆绝缘电气强度：导体之间1min1kv不击穿导体与屏蔽1min 3kv不击穿3.充油电缆绝缘电阻：每根芯线与其余线芯接地，HYAT电缆大于3000MΩ.k。
低烟无卤电缆代号、名称及含义：项目代号含义系列代号DLDWLDK低烟低卤低烟无卤控制电缆绝缘材料VJEF聚氯乙烯交联聚烯烃丁腈热塑体护套材料VGS聚氯乙烯热固性护套热塑性护套屏蔽材料PP2铜网或镀锡铜网铜带/塑复合带铠装材料2232钢带细钢丝导体种类ABR独股导体7股绞合导体多股绞合导体；生产范围截面(mm2)：0.5、1.0、1.5、2.5、4、6、10、16、25。
低烟无卤电缆主要用途：该产品阻燃性能优越，燃烧时烟度甚少，无腐蚀性气体逸出，广泛应用于核电站、地铁车站、电话交换机及计算机控制中心、高层建筑大楼、宾馆、广播电视台、重要军事设施、石油平台等，以及人员较集中，空气密度低的场所。
低烟无卤电线特性：(1) 抗张强度比一般PVC电线大：一般PVC电线抗张强度大于1.05Kgf/mm2，而低烟无卤电线抗张强度大于1.2Kgf/mm2；(2) 具有良好的耐候性(-30℃~105℃)；(3) 具备良好的柔软度(硬度为80—90)；(4) 具有非移性(因为此产品配方中不用添加可塑剂，故不会有移形性)；(5) 燃烧时不会产生有毒黑烟(会产生少量白色烟雾)；(6) 具有较高的体积电阻率：PVC电线一般为1012~1015Ω/cm3，低烟无卤电线大于1016Ω/cm3；(7) 具有良好的耐高压特性：PVC电线一般耐10KV以上，而低烟无卤电线高达15KV以上；(8) 具有良好的弹性和粘性。
线性变换原理线性变换原理.线性变换的原理很简单，比如说，在工程测量中，常会遇到4-20mA的传感器，如压力传感器或位移传感器等，要转换为0-50MPa的物理量。用高中学过的直线方程两点式就可以了。已知两点（4，0）和（20，50），求（x,y）。线性变换子程序以下介绍线性变换的子程序编写。新建一个功能块（如FC30）,在FC30中编写线性变换子程序。如.1所示为线性转化子程序输入变量。，为了便于使用，输入变量的数据类型都定义为浮点数。
Main products are: mine cable MHYV, MHY MHYA32, MHY32, MHYVP, MHYVR, MHYVRP, MKVV, MKVV22, MKVV32, MKVVR, MKVVP etc., all kinds of products are all in the coal Ann mark certificate and complete specifications, the major products are widely used in coal mine and coal mine monitoring and control. The products are used in dozens of coal groups and mines, which have been highly praised.
广东省：广州、深圳、清远、韶关、河源、梅州、潮州、汕头、揭阳、汕尾、惠州、东莞、珠海、中山、江门、佛山、肇庆、云浮、阳江、茂名、湛江贵州省：贵阳、六盘水、遵义、安顺河北省石家庄、邯郸、唐山、保定、秦皇岛、邢台、张家口、承德、沧州、廊坊、衡水。