***PC-PC德国科思创(拜耳)1695
PC德国拜耳 KU1-1216 透镜和护目镜品级，紫外线稳定，中粘度，有本色和透明色，含特殊紫外线吸收剂，能阻隔400nm以下的紫外线，用于太阳镜等制品。
PC德国拜耳 LQ 2847 透镜和护目镜品级，紫外线稳定，易脱模，中粘度，用于眼科镜等。
PC德国拜耳 LQ 3147 透镜和护目镜品级，紫外线稳定，易脱模，中粘度，用于眼科镜
PC德国拜耳 LQ 3187 透镜和护目镜品级，紫外线稳定，易脱模，中粘度，晶状透明,含特殊紫外线吸收剂，能阻隔00nm以下的紫外线，用于太阳镜等制品。
PC德国拜耳 AL2447 汽车照明等级，紫外线稳定，易脱模，易流动，晶状体透明。
PC德国拜耳AL2647 汽车照明等级，紫外线稳定，易脱模，易流动，晶状体透明。
PC德国拜耳 DP1-1262 医疗设备等级，中粘度，颜色稳定，适合透析机外壳等的成型
PC德国拜耳 RX-1805 医疗设备等级，高粘度，颜色稳定，适合于三通旋塞和旋塞电池的
* * PC-PC Bayer 1695pc Bayer 6557 injection or extrusion molded, halogen free flame retardant UL94V-0, medium viscosity, UV stable, easy to flow. PC Bayer 6585 injection or extrusion molding, flame retardant class UL94V-0, high viscosity, easy to flow; used for electronic and electrical industrial flame retardant components. PC Bayer 6717 injection or extrusion molding, flame retardant class UL94V-0, high viscosity, UV stability, easy to flow. PC Bayer 8025 injection or extrusion molding, 20% glass fiber reinforced, high viscosity, good impact strength, easy demoulding; used for industrial accessories, electronic and electrical appliances. PC Bayer 8035 injection or extrusion molding, 30% glass fiber reinforced, high viscosity, high strength, easy demoulding, for industrial accessories, electronic and electrical appliances. PC Bayer 8345 injection or extrusion molding, 35% glass fiber reinforced, flame retardant class UL94V-0, high viscosity, easy to flow.Uv-stabilized, easy mold release, medium viscosity, lens transparency, safety goggles and other applications. PC German Bayer Ku1-1216 lens and goggles grade, UV stability, medium viscosity, with natural color and transparent color, with special UV absorbent, can block 400 nm of UV, used in sunglasses and other products. PC German Bayer LQ 2847 lens and goggles grade, UV stability, easy to demoulding, medium viscosity, for ophthalmic glasses and so on. PC German Bayer LQ 3147 lens and goggles grade, UV stability, easy mold release, medium viscosity, for ophthalmic glasses PC German Bayer LQ 3187 lens and goggles grade, UV stability, easy mold release, medium viscosity, crystal Transparent, with a special UV absorbent, can block the UV below 00nm, used in sunglasses and other products. PC German Bayer Al2447 automotive lighting grade, UV stability, easy mold release, easy flow, transparent lens. PC German Bayer Al2647 automotive lighting grade, UV stability, easy mold release, easy flow, transparent lens. German Bayer DP1-1262 medical equipment grade, medium viscosity, color stability, suitable for dialysis machine shell and other molding PC German Bayer RX-1805 medical equipment grade, high viscosity, color stability, suitable for three-way cocks and Cocker batteries
产品加工
主要加工方式
注塑： 主要用于制造较精密的、承受较大冲击负荷的中、小型制品
吹塑： 包装容器（瓶）
挤出： 板、管、棒等型材以及薄膜
注塑性能： ：PC是结晶性塑料，有明显的熔点，220℃时熔化，350℃时就分解；一般加工温度为250℃--320℃；它吸水，少量的水分可以引起它在高温时分解，在注塑时，必需要烘干，烘干温度可以用120℃烘干4-5小时即可；
PC料的熔融粘度大，注塑时，需要用较大的压力；
PC在加工时，如果条件允许，可以用模温机提高模具温度，以降低产品的残余应力；如果是有嵌件的制品，嵌件的直径小于1-2mm,可以不考虑预热，大一点嵌件应考虑预热，否则，会出现应力开裂；
PC的收缩率与加工条件和制品的壁厚无关，它的纵横向收缩率比较接近，因此，可以加工成精度很高的制品；它的收缩率为：0.5‰；溢边值为：0.05mm。
PC主要应用分类：
导光PC 主要用作 LCD 如：出光 LC1500
遮光PC 主要用做LCD 日本出光 URX2501
光扩散PC 主要用作LED灯罩 扩散率80~85% 如：日本帝人ML-1103
吹瓶PC 主要用作 矿泉水瓶 德国拜耳1239
光学PC 主要用作照相机、显微镜、望远镜的镜头，太阳眼镜镜片，汽车灯 透明度 90%光碟级 专做光盘 流动性溶指60以上 三菱H-4000 价格38 基础创新OQ1023 价格 23
其他分类：防静电PC，导电PC，加纤防火PC，抗紫外线耐候PC，食品级PC等
Product processing main processing mode, injection molding: mainly used for manufacturing more precise, bear larger impact load of medium and small products, blow molding: packaging container -LRB-bottle) extrusion: plates, tubes, rods and other profiles and film injection molding propertiPC: PC is a crystalline plastic, there is an obvious melting point, 22C ° c melting, 35C ° c decomposition; The general processing temperature is 250 ° C-320 ° C. it absorbs water, a small amount of water can cause it to decompose at high temperature PC melt viscosity, injection molding, the need for greater pressure, PC processing, if the conditions allow, can be used to raise the mold temperature, mold temperature to reduce the residual stress of the product, if there are embedded products, if the diameter of insert is less than 1-2mm, preheating should not be considered. If larger insert is considered preheating, otherwise, stress cracking will occur, its longitudinal and transverse shrinkage rates are close, therefore, it can be processed into high-precision products; its shrinkage rate is: 0.5‰ ; overflow value is: 0.05 mm. PC main application classification: light-guide PC mainly used as LCD, such as: LC1500 light-out PC mainly used as LCD, Japan light-out URX2501 light diffusion PC mainly used as LED lampshade, the diffusivity is 80 ~ 85% . For example, the Japanese Imperial ML-1103 blowing bottle PC is mainly used for mineral water bottle, the German Bayer 1239 optical PC is mainly used for camera, microscope, telescope lens, sunglasses lens, etc. , automotive Lights, transparency 90% CD-ROM class, specialized cd-rom, liquidity dissolve index 60 above, Mitsubishi H-4000 Price 38 Basic Innovation OQ1023 price 23 other categories: anti-static PC, conductive PC, plus fiber fire PC, anti-uv weather PC, food-grade PC