PET美国杜邦953 NC010

商品描述价格说明联系我们品牌杜邦规格25加工定制否品名PET牌号953特性级别增强级,阻燃级用途级别汽车部件,电子电器部件是否进口否可售卖地北京;天津;河北;山西;内蒙古;辽宁;吉林;黑龙江;上海;江苏;浙江;安徽;福建;江西;山东;河南;湖北;湖南;广东;广西;海南;重庆;四川;贵州;云南;西藏;陕西;甘肃;青海;宁夏;新疆类型标准料填料/增强材料：玻璃纤维增强材料,33% ;填料按重量测试类别测试条件测试标准单位测试结果物 理 性 能密度（比重）23±2℃，50±5% RHASTM D792g/cm³1.28收缩率 - 流动ASTM D955%0.20测试类别测试条件测试标准单位测试结果机 械 性 能断裂伸长率50 mm/min,3.2mmASTM D638%6.0拉伸强度50 mm/min,3.2mmASTM D638MPa131弯曲模量10 mm/min，3.2mmASTM D790MPa7240测试类别测试条件测试标准单位测试结果Advantages of DuPont PET plastic raw materials in the United States:1. It has good mechanical properties, with an impact strength 3-5 times that of other films, and good bending resistance.2. Resistant to oil, fat, enoic acid, dilute alkali, and most solvents.3. It has excellent resistance to high and low temperatures, and can be used for a long time within the temperature range of 120 ℃. It can withstand high temperatures of 150 ℃ and low temperatures of -70 ℃ for short-term use, and has little impact on its mechanical properties at high and low temperatures.4. Low permeability of gas and water vapor, with excellent gas resistance, water, oil, and odor resistance.5. High transparency, can block ultraviolet rays, and has good glossiness.6. It is non-toxic, odorless, and has good hygiene and safety, and can be directly used for food packagingCharacteristics of DuPont PET plastic raw materials in the United States:PET is a milky white or pre yellow highly crystalline polymer with a smooth and shiny surface. Creep resistance, fatigue resistance, wear resistance, and dimensional stability are good, with low wear and high hardness. It has the greatest toughness among thermoplastic materials: good electrical insulation performance, less affected by temperature, but poor corona resistance. Non toxic, weather resistant, stable against chemicals, low water absorption, resistant to weak acids and organic solvents, but not resistant to hot water immersion or alkali.PET resin has a high glass transition temperature, slow crystallization rate, long molding cycle, long molding cycle, high molding shrinkage rate, poor dimensional stability, brittle crystallization molding, and low heat resistance.Through the improvement of nucleating agents, crystallization agents, and glass fiber reinforcement, PET not only possesses the properties of PBT, but also has the following characteristics.1. The thermal deformation temperature and long-term use temperature are the highest among thermoplastic general engineering plastics2. Due to its high heat resistance, reinforced PET is immersed in a soldering bath at 250 ℃ for 10 seconds without deformation or discoloration, making it particularly suitable for preparing electronic and electrical parts for soldering:3. The bending strength is 200MPa, the elastic modulus reaches 4000MPa, and the creep and fatigue resistance are also good. The surface hardness is high, and the mechanical properties are similar to those of thermosetting plastics.4. Due to the fact that ethylene glycol used in the production of PET is almost half cheaper than butanediol used in the production of PBT, PET resin and reinforced PET are the lowest priced engineering plastics with high cost-effectivenessPET,美国杜邦,953 NC010,PET美国杜邦,美国杜邦953 NC01