| 重量 : | 0.2（kg） | 类型 : | 流量计 |
| 型号 : | GF-8341-2214 | 测量精度 : | 0.1 |
| 尺寸 : | 167.5（mm） | 品牌 : | Gilmont |
| 测量电流范围 : | 1（A） | 测量电阻范围 : | 10（Ω） |
| 测量电压范围 : | 1（V） |
Thermo Scientific* Gilmont* 65mm Construction Industrial Direct Reading Flowmeters With Standard w/standard valve; Air flow rate: 5 to 60SmL/min.
具体参数如下：
5FL4OWMETERSInternational
FLOWMETERS
Rotameter Introduction
Corrections for Gas Flow
Gas Flow from Air Flow:
Corrections for Liquid Flow
Liquid Flow from Water Flow:
Corrections for Temperature and Pressure:
Correction for Temperature
(Note: for liquids the effect of pressure is negligible):
General Correction equations for approximating gas
or liquid flow from air or water flow readings.
IMPORTANT INFORMATION ON ROTAMETERS
The Variable-Area type flowmeter, or Rotameter, is one
of the most economical and reliable of flow
measurement instruments. In various configurations it
can be designed to withstand high pressures, corrosive
fluids, high temperatures, and is completely
independent of factors influencing electronic meters.
They can be calibrated to measure nearly any gas or
liquid, because their principles of operation are simple
and well understood. The flow indication is obtained
from a balance of the fluid forces underneath the float
with gravity.
This is done using a uniformly tapered tube, a float
whose diameter is nearly identical to the tube ID at the
inlet, and a scale to correlate float height. The flow tube
is traditionally placed in a vertical position and fluid
enters from the bottom, forcing the float up in the tube
until a sufficient annular opening exists between the
float and tube to allow the total volume of fluid to flow
past the float. At this point the float is in an equilibrium
position and its height is proportional to the flow rate.
DENSITY TERMS
= density of gas in gm/ml at std. cond.
= density of liquid in gm/ml at std. cond.
= density of liquid in gm/ml at T
= density of float = 2.53 for glass, 3.98 for ruby,
8.02 for stainless steel, 14.9 for tungsten carbide
VISCOSITY TERMS
= viscosity of gas in cp at std. cond.
= viscosity of liquid in cp at std. cond.
= viscosity of liquid in cp at T
FLOWM5ETER5S
Multiply
Reading ByWorking Pressure of Flowmeter – PSIG
Pressure at Which Meter Was Calibrated – PSIG
FLOWMETER PRESSURE CORRECTION
SPECIFIC GRAVITY CORRECTION FACTORS
Laboratory Flowmeters
FLOWMETERS
• High-accuracy correlated flowmeters – ±2% of reading!
• Wide selection of flow ranges—measure air from 0.02 ml/min to
675 LPM or water from 0.0002 ml/min to 20 LPM
• Excellent chemical compatibility with glass and PTFE construction
Product Description
Unshielded Flowmeters
Choose unshielded flowmeters for high purity and corrosion resistance in
low-pressure applications. PTFE stops accept taper joints to make quick
glass-to-glass connections.
PRODUCT SPECIFICATIONS
Flow rate* Unshielded flowmeters Shielded flowmeters Shielded flowmeters with valves
Tube Float Air Water Catalog Catalog Ports Catalog Ports
size included (ml/min) (ml/min) number Max psi number NPT(M) Max psi number NPT(M) Max psi
10 Glass 0.2-90 0.002-1.1 GF-2000 15 GF-2060 1⁄4" 125 GF-9060 1⁄8" 125
316 SS 0.36-160 0.004-2.3
11 Glass 1-280 0.01-4.0 GF-2100 15 GF-2160 1⁄4" 125 GF-9160 1⁄8" 125
316 SS 2-500 0.02-8.6
12 Glass 20-2100 0.4-40 GF-2200 15 GF-2260 1⁄4" 100 GF-9260 1⁄8" 100
316 SS 36-3700 0.86-86
13 Glass 200-14,000 2-300 GF-2300 15 GF-2360 1⁄4" 75 GF-9360 1⁄8" 75
316 SS 360-25,000 4-640
14 Glass 1000-36,000 10-850 GF-2400 15 GF-2460 1⁄2" 60 GF-9460 1⁄4" 60
316 SS 1800-64,000 21-1820
15 Glass 3000-77,000 30-1900 GF-2500 15 GF-2560 1⁄2" 50 GF-9560 1⁄4" 50
316 SS 5300-137.000 64-4100
NOTE: For pressure drop of each flowmeter, please call our Application Specialists. *When using stainless steel float, refer to included correlation table for proper reading.
Flow rate* Unshielded flowmeters Shielded flowmeters Shielded flowmeters with valves
Tube Float Air Water Catalog Catalog Ports Catalog Ports
size included (ml/min) (ml/min) number Max psi number NPT Max psi number NPT Max psi
Micro Ruby 0.02-15 0.0002-0.12 GF-3000 15 GF-3060 1⁄4 (M) 125 GF-9760 1⁄8 (M) 125
0 Glass 0.2-100 0.002-1.1 GF-1000 15 GF-1060 1⁄4 (M) 125 GF-7060 1⁄8 (M) 125
316 SS 0.36-180 0.004-2.3
1 Glass 1-280 0.01-4.0 GF-1100 15 GF-1160 1⁄4 (M) 125 GF-7160 1⁄8 (M) 125
316 SS 2-500 0.02-8.6
2 Glass 10-1900 0.2-36 GF-1200 15 GF-1260 1⁄4 (M) 100 GF-7260 1⁄8 (M) 100
316 SS 20-3400 0.43-77
3 Glass 200-14,000 3-300 GF-1300 15 GF-1360 1⁄4 (M) 75 GF-7360 1⁄8 (M) 75
316 SS 360-25,000 6-640
4 Glass 1000-36,000 10-850 GF-1400 15 GF-1460 1⁄2 (M) 60 GF-7460 1⁄4 (M) 60
316 SS 1800-64,000 21-1820
5 Glass 3000-77,000 30-1900 GF-1500 15 GF-1560 1⁄2 (M) 50 GF-7560 1⁄4 (M) 50
316 SS 5300-137,000 64-4100
6 Glass 25,000-330,000 500-8000 — — GF-1660 1⁄2 (F) 50 — — —
316 SS 50,000-675,000 1500-20,000
Shielded Flowmeters
Use these flowmeters for higher pressure applications. The clear polycarbonate
shield adds strength and protects the tube from damage.
Fluid contacts only the borosilicate glass tube, PTFE body, and VITON®
fluoroelastomer O-rings. End bushings are polypropylene with PTFE inserts.
Shielded Flowmeters with Valves
Choose these flowmeters for greater control; micrometer capillary valves ensure
precise, reproducible measurement and flow control. Shields are clear
polycarbonate; valve consists of a precision-bore glass tube for the fluid and a
precision-ground rod of PCTFE (PTFE for sizes 4, 5, 14, and 15). The 20-turn
micrometer valve can be adjusted from 0.1 to of maximum flow. You can
interchange flowtubes among valve assemblies of the same size.
Direct Reading Flowmeters
Read air and water flow directly with these compact meters. Accuracy is ±5% of
reading or 2 mm of the scale length, whichever is greater.
Correlated Flowmeters
Extremely accurate . . . . ± 2% of reading or ±1 scale division, whichever is
greater. Determine flow values for air and water from the computerized
calibration table enclosed with each flowmeter. Tables are included. See page 58
to order our flow analysis software to generate flow charts specific to your
individual applications.
For technical application
questions, contact Barnant
at 800-637-3739
Direct Reading Correlated
Accuracy:±5% of reading or 2mm of scale length whichever is greater. ±2% of reading or ±1 scale division, whichever is greater.
For micro: ±5% of reading or ±2 scale division
(Air); ±10% of reading or ±3 scale division (water).
Repeatability:±1% of reading or ±0.5 scale division, whichever is greater.
Turndown Ratio:Better than 25:1
Pressure Rating:See tables, page 56
Operating Temperatures:-15°F to 150°F (-26°C to 65°C) at full pressure rating.
Connections:Unshielded Use Taper Joint Adapters–see chart at right
Shielded 3/8” I.D. tubing on Sizes 0-3, and Micro to 13,
5/8” I.D. tubing on Sizes 4-5, and 14 to 15, or see
chart at right for coupling adapters.
Shielded with Valve 1/8” NPT(M) Sizes 0-3, Micro–13
1/4” NPT(M) Sizes 4-5, 14-15
Shipping Weight:Unshielded 0.5 lb. (0.3 kg)
Shielded 1.0 lb. (0.5 kg)
Shielded with Valve 1.0 lb. (0.5 kg)
GF-4004Flowmeter stand kit. Includes one base, one rod, and two mounting clamps
GF-4001Flowmeter base
GF-4002Rod, 18"L
GF-4003Mounting clamp. Includes wood screws
Laboratory Flowmeters
FLOWMETERS
PRODUCT SPECIFICATIONS
MATERIALS OF CONSTRUCTION
Borosilicate glass Flowtube
Glass/316 SS (Ruby-micro size only) Floats
PTFE End blocks/stops
PTFE Inlet/Outlet
Polycarbonate Shield
Polypropylene Shield ends
PTFE, PCTFE, Glass Valve
Viton®O-rings
DIMENSIONS
Dimensions
Unshielded Shielded Shielded with valves
Flowmeter Stand Kit and Components
The flowmeter stand kit contains everything you need to mount your GILMONT®
flowmeter on a stand, a benchtop, or a wall. The base is machined from rugged
aluminum. A built-in ‘‘bubble level’’ ensures that the base is level for maximum
accuracy. Configure base to accept three rod and clamp assemblies for
unshielded or shielded flowmeters. Mount valved flowmeters directly—base
accepts two large flowmeters (size 4, 5, 14, or 15) or three of the smaller
flowmeters. Mounting clamps hold flowmeters firmly in place without obstructing
your view of the flowmeter scale or damaging the flowtube or shield.
Clamps are L-shaped with mounting holes bored into them for mounting
flowmeters to a wall or panel (wood screws included).
TAPER JOINTS AND PTFE COUPLING ADAPTERS
Cat. No. Tube Size Connection
Taper joints for unshielded flowmeters
GF-1121 Micro., 0, 10/30 taper
1, 10, 11
GF-1221 2 and 12 12/30 taper
GF-1321 3 and 13 14/35 taper
GF-1421 4 and 14 19/38 taper
GF-1521 5 and 15 24/40 taper
PTFE coupling adapters for shielded flowmeters
GF-4010 Micro., 0, 1, 2, 1/4” NPT(F)
3, 10, 11, 12, 13
GF-4020 4, 5, 14, 15 1/2” NPT(F)
For technical application
questions, contact Barnant
at 800-637-3739
Accessories
GF-4001 Flowmeter Baseis made of rugged
aluminum. Mount flowmeters directly—base accepts
three flowmeters. Built-in bubble level.
GF-4000 Flowrate Analysis Softwaremakes
flow analysis simple. You can produce flow rate
tables and custom scales based on your temperature,
pressure, viscosity and density conditions; float
material; and the gas or liquid being measured.58
Max flow rate 65mm, 303 stainless steel flowmeters
(ml/min) Without valves With precision valves
Air Cat. no. Cat. no.
Glass 95 1.1 100 GF-6340-1100 GF-6341-1100
SS 230 4.9
Glass 280 3.9 110 GF-6340-1110 GF-6341-1110
SS 620 15
Glass 1000 17 115 GF-6340-1115 GF-6341-1115
SS 2000 55
Glass 2200 43 120 GF-6340-1120 GF-6341-1120
SS 4200 120
Glass 6500 140 125 GF-6340-1125 GF-6341-1125
SS 12,000 360
Glass 14,000 320 130 GF-4340-1130 GF-4341-1130
SS 25,000 800
Glass 25,000 590 135 GF-4340-1135 GF-4341-1135
SS 46,000 1400
•• •
Gilmont®Accucal®Flowmeters
FLOWMETERS
• Correlated and direct reading all in one easy-to-read meter
• Accuracy up to ±2% of reading!
• Interchangeable scales—customize your application
• Extremely low pressure drops—ideal for procedures with
critical pressure values
Two direct reading
scales are included with
each flowmeter. (English
and metric units)
These flowmeters can be
mounted on a panel or base.
Correlated and Direct Readingin one easy to use flowmeter. Each meter includes
correlation charts for air and water and two direct-reading scales—an air scale and a water
scale. Easily change between correlated and direct-reading scales depending on your application.
Meters are available in 65mm and 150mm scale lengths.
Each direct-reading scale indicates flow rates in metric and English units, for both glass and
stainless steel floats under standard operating conditions. Use the new GF-4000 software to create
your own custom scales.
Excellent Accuracyis achieved with our second-generation correlation techniques
and the factory calibration of the tube. Accuracy can be expressed as a percent of
reading—not of full-scale! With correlated use, accuracy is ±2% of reading or ±1%
scale division, whichever is greater. With direct-reading use, ±2 divisions accuracy is
±5% of reading or ±3 mm on scale, whichever is greater. All flowtubes have serial
numbers for traceability to calibration, accuracy, and manufacturing data.
Quality Industrial Designensures use in most tough applications. The clear polycarbonate
front shield provides a 90° view of the scales on the stainless meters.
Meters are designed for easy flowtube exchange or replacement. The end stop has a large diameter
to let you center the flowtube quickly and more accurately than most flowmeters. All flowtubes
are interchangeable within the same frame size. Call our Application Specialist to order a
replacement flowtube or to upgrade your unit.
Mount flowmeters on a panel or on our flowmeter base (see below). Invert frame for vacuum
applications or when back pressure compensation is required.
Advanced Metering Valvesare available with GILMONT®flowmeters. The shallow
taper design gives you linear control over 80% of the usable range. Valves are 14-turn.
NOTE: For pressure drop of each flowmeter, please call our Application Specialists.
H2O
Float
Tube
sizeFor technical application
questions, contact Barnant
at 800-637-3739
150-mm, 303 stainless steel flowmeters
Tube Without valves With precision valves
size Cat. no. Cat. no.
200 GF-6540-1200 GF-6541-1200
210 GF-6540-1210 GF-6541-1210
215 GF-6540-1215 GF-6541-1215
220 GF-6540-1220 GF-6541-1220
225 GF-6540-1225 GF-6541-1225
230 GF-6540-1230 GF-6541-1230
235 GF-6540-1235 GF-6541-1235
240 GF-6540-1240 GF-6541-1240
250 GF-6540-1250 GF-6541-1250
Max flow rate (ml/min)
Air
Glass 95 1.1
SS 230 4.9
Glass 280 3.9
SS 620 15
Glass 1000 17
SS 2000 55
Glass 2200 43
SS 4200 120
Glass 6500 140
SS 12,000 360
Glass 14,000 320
SS 25,000 800
Glass 25,000 590
SS 46,000 1400
Glass 40,000 960
SS 73,000 2200
Glass 85,000 2000
SS 150,000 4700
H2O
59
Gilmont®Accucal®Flowmeters
FLOWMETERS
▼
▼
Accuracy:The greater of ±2% of reading or ±1 division
(correlated use); the greater of ±5% of reading
±2 division of scale (direct reading use)
Repeatability:±1% of reading or ±0.5 scale division,
whichever is greater
Turn-Down Ratio:Better than 25:1
Maximum Pressure:200 psig at 250°F
Maximum Operating Temperature:250°F (121°C)
Connections:1⁄4" NPT(F) for 240 and 250 tube sizes;
1⁄8 NPT(F) for all others
Shipping Weight:65mm flowmeters: 1 lb (0.5 kg)
150mm flowmeters: 2 lb (1.0kg)
*Other Floats/materials available. Call our application specialists for details.
Mount these flowmeters
on a panel or base.
Flowmeter base
GF-4001
PRODUCT SPECIFICATIONS
DIMENSIONS
Flowmeter End Inlet/Outlet
Type Flowtube Floats Blocks Connections Valve O-rings
303 SS Borosilicate glass Glass/316 SS 303 SS 303 SS PCTFE/PTFE Viton®
(303 SS PCTFE/PTFE
for tube sizes 240 and 250)
MATERIALS OF CONSTRUCTION
Dimensions - inches (mm)
Flowmeter A B C D E F G H
65 mm scale (all tube sizes) 5.65 (143.5) 0.60 (15.2) 4.50 (114.3) 1/8 - 27 NPT 0.78 (19.8) 1.00 (25.4) 1.75 (44.4) 1.25 (31.7)
150 mm scale (200-235 tubes) 10.02 (254.5) 0.60 (15.2) 8.81 (223.8) 1/8 - 27 NPT 0.78 (19.8) 1.00 (25.4) 1.75 (44.4) 1.25 (31.7)
150 mm scale (240-250 tubes) 12.64 (321.1) 0.79 (20.1) 11.00 (279.4) 1/8 - 27 NPT 0.95 (24.1) 1.50 (38.1) 2.13 (54.1) 1.75 (44.4)
Float
For technical application
questions, contact Barnant
at 800-637-3739
60•• •
Industrial Flowmeters
FLOWMETERS
• Accuracy: ± 5% of full scale, 0.5% of scale repeatability
• Flow ranges: Air – 1 cc to 60 L/MIN, 0.025 cc to 1.8 L/MIN
water
• Pressure ratings to 200 psig (max.)
• Temperature ratings to 250°F (max.)
• Calibrated (mm scale) or direct reading (metric)
• Ten to one flowrange on all units
For All Your Industrial and
Laboratory Applications
Product Description
Choose GILMONT®flowmeters for all your industrial and laboratory
applications. Measure and control liquids and gases in a wide range of
applications with precision and repeatability.
Gilmont offers flowmeters in a variety of materials, including Aluminum,
Brass, and SS Standard and high precision metering valves, and a wide
range of direct reading scales are available for most models.
The 65mm and 150mm series have precision glass metering tubes,
glass and SS floats. Front shields have 1.5X magnification for more
accurate readings.
These flowmeters follow industry standard dimensions for easy
retrofitting and direct replacements. Standard panel mounting hardware
is supplied with each meter, and tripod bases are available for benchtop
applications. Order part number GF-8008
65 mm Calibrated
This 65mm size incorporates all features and quality of the larger
flowmeters, in a compact size. All tubes are protected within the unitized
holder and strong aluminum frame. A lens magnifier makes the
scales easy to read. Calibration tables for both air and water are
enclosed with each flowmeter.
65 mm Direct Reading
Utilizing a vast reference library of liquids and“noble” gases, we are
able to provide flowmeters to meet specific, rather than general, flow
ranges. All Direct Reading 65mm flowmeters are available in liters for
international applications and acceptance.
150 mm Calibrated
This versatile meter is functionally and dimensionally interchangeable
with other current designs while providing many innovative features.
The glass metering tubes have integral float guides to assure a ±5%
accuracy of full scale. Glass and Stainless Steel floats are standard.
Calibration tables for both air and water are enclosed with each
flowmeter.
Materials of Construction
• Wetted End Blocks, Fittings and Internal Parts –
Anodized Aluminum, Brass, 316 SS.
• Seal Materials – Buna-N or Viton®.
• Side Plates – Aluminum
• Metering Tube – Borosilicate Glass enclosed in the
Unitized Aluminum Frame
• Piping Connections – Aluminum, Brass or 316SS,
1/8 NPT(F) horizontal on inlet and outlet.
• Float Material – Black Glass, 316 SS
or Tungsten Carbide
150mm Construction max. operating operating flow rate scale reading of full scale and water
PRODUCT SPECIFICATIONS
65 & 150 mm Flowmeters
Dimensional Drawing
Max Flow
SML / min
Air WATER ALUMINUM BRASS STAINLESS ALUMINUM BRASS STAINLESS ALUMINUM BRASS STAINLESS
STEEL STEEL STEEL
8.1 - 145 0.1 - 2.4 GF-8320-1001 GF-8330-1001 GF-8340-1001 GF-8321-1001 GF-8331-1001 GF-8341-1001
30.2 - 298 0.46 - 7.7 GF-8320-1002 GF-8330-1002 GF-8340-1002 GF-8321-1002 GF-8331-1002 GF-8341-1002
45 - 522 0.8 - 12 GF-8320-1101 GF-8330-1101 GF-8340-1101 GF-8321-1101 GF-8331-1101 GF-8341-1101
28 - 1249 0.6 - 27 GF-8320-1201 GF-8330-1201 GF-8340-1201 GF-8321-1201 GF-8331-1201 GF-8341-1201
90 - 2520 3.7 - 71 GF-8320-1202 GF-8330-1202 GF-8340-1202 GF-8321-1202 GF-8331-1202 GF-8341-1202
845 - 6318 4 - 147 GF-8320-1401 GF-8330-1401 GF-8340-1401 GF-8321-1401 GF-8331-1401 GF-8341-1401
1973 - 1205842 - 364 GF-8320-1402 GF-8330-1402 GF-8340-1402 GF-8321-1402 GF-8331-1402 GF-8341-1402
2272 - 24680127 - 745 GF-8320-1501 GF-8330-1501 GF-8340-1501 GF-8321-1501 GF-8331-1501 GF-8341-1501
6082 - 58500176 - 1866 GF-8320-1502 GF-8330-1502 GF-8340-1502 GF-8321-1502 GF-8331-1502 GF-8341-1502
5 - 100 GF-8320-2009 GF-8330-2009 GF-8340-2009 GF-8321-2009 GF-8331-2009 GF-8341-2009
20 - 250 GF-8320-2010 GF-8330-2010 GF-8340-2010 GF-8321-2010 GF-8331-2010 GF-8341-2010
20 - 500 GF-8320-2109 GF-8330-2109 GF-8340-2109 GF-8321-2109 GF-8331-2109 GF-8341-2109
100 - 1000 GF-8320-2110 GF-8330-2110 GF-8340-2110 GF-8321-2110 GF-8331-2110 GF-8341-2110
500 - 10000GF-8320-2410 GF-8330-2410 GF-8340-2410 GF-8321-2410 GF-8331-2410 GF-8341-2410
2000 - 40000GF-8320-2510 GF-8330-2510 GF-8340-2510 GF-8321-2510 GF-8331-2510 GF-8341-2510
0.025 - 0.5 GF-8320-2004 GF-8321-2004 GF-8330-2004 GF-8331-2004 GF-8340-2004 GF-8341-2004
0.4 - 6 GF-8320-2014 GF-8330-2014 GF-8340-2014 GF-8321-2014 GF-8331-2014 GF-8341-2014
1 - 25 GF-8320-2114 GF-8330-2114 GF-8340-2114 GF-8321-2114 GF-8331-2114 GF-8341-2114
5 - 60 GF-8320-2214 GF-8330-2214 GF-8340-2214 GF-8321-2214 GF-8331-2214 GF-8341-2214
20 - 250 GF-8320-2414 GF-8330-2414 GF-8340-2414 GF-8321-2414 GF-8331-2414 GF-8341-2414
100 - 1500 GF-8320-2516 GF-8330-2516 GF-8340-2516 GF-8321-2516 GF-8331-2516 GF-8341-2516
8.1 - 140 0.12 - 2.34 GF-8520-1100 GF-8530-1100 GF-8540-1100 GF-8521-1100 GF-8531-1100 GF-8541-1100 GF-8522-1100 GF-8532-1100 GF-8542-1100
33 - 264 0.28 - 4.7 GF-8520-1200 GF-8530-1200 GF-8540-1200 GF-8521-1200 GF-8531-1200 GF-8541-1200 GF-8522-1200 GF-8532-1200 GF-8542-1200
70 - 825 0.8 - 16 GF-8520-1300 GF-8530-1300 GF-8540-1300 GF-8521-1300 GF-8531-1300 GF-8541-1300 GF-8522-1300 GF-8532-1300 GF-8542-1300
201 - 1682 3.5 - 46 GF-8520-1406 GF-8530-1406 GF-8540-1406 GF-8521-1406 GF-8531-1406 GF-8541-1406 GF-8522-1406 GF-8532-1406 GF-8542-1406
480 - 4562 5.4 - 133 GF-8520-1500 GF-8530-1500 GF-8540-1500 GF-8521-1500 GF-8531-1500 GF-8541-1500 GF-8522-1500 GF-8532-1500 GF-8542-1500
288 - 7590 6 - 217 GF-8520-1606 GF-8530-1606 GF-8540-1606 GF-8521-1606 GF-8531-1606 GF-8541-1606 GF-8522-1606 GF-8532-1606 GF-8542-1606
462 - 2253615 - 541 GF-8520-1700 GF-8530-1700 GF-8540-1700 GF-8521-1700 GF-8531-1700 GF-8541-1700 GF-8522-1700 GF-8532-1700 GF-8542-1700
3542 - 59494 103 - 1881GF-8520-1800 GF-8530-1800 GF-8540-1800 GF-8521-1800 GF-8531-1800 GF-8541-1800 GF-8522-1800 GF-8532-1800 GF-8542-1800
1 - 100 GF-8520-2117 GF-8530-2117 GF-8540-2117 GF-8521-2117 GF-8531-2117 GF-8541-2117 GF-8522-2117 GF-8532-2117 GF-8542-2117
20 - 200 GF-8520-2217 GF-8530-2217 GF-8540-2217 GF-8521-2217 GF-8531-2217 GF-8541-2217 GF-8522-2217 GF-8532-2217 GF-8542-2217
50 - 800 GF-8520-2317 GF-8530-2317 GF-8540-2317 GF-8521-2317 GF-8531-2317 GF-8541-2317 GF-8522-2317 GF-8532-2317 GF-8542-2317
200 - 2500 GF-8520-2417 GF-8530-2417 GF-8540-2417 GF-8521-2417 GF-8531-2417 GF-8541-2417 GF-8522-2417 GF-8532-2417 GF-8542-2417
400 - 4800 GF-8520-2517 GF-8530-2517 GF-8540-2517 GF-8521-2517 GF-8531-2517 GF-8541-2517 GF-8522-2517 GF-8532-2517 GF-8542-2517
800 - 10000GF-8520-2617 GF-8530-2617 GF-8540-2617 GF-8521-2617 GF-8531-2617 GF-8541-2617 GF-8522-2617 GF-8532-2617 GF-8542-2617
1000 - 23000GF-8520-2717 GF-8530-2717 GF-8540-2717 GF-8521-2717 GF-8531-2717 GF-8541-2717 GF-8522-2717 GF-8532-2717 GF-8542-2717
5000 - 60000GF-8520-2817 GF-8530-2817 GF-8540-2817 GF-8521-2817 GF-8531-2817 GF-8541-2817 GF-8522-2817 GF-8532-2817 GF-8542-2817
0.5 - 10 GF-8520-2227 GF-8530-2227 GF-8540-2227 GF-8521-2227 GF-8531-2227 GF-8541-2227 GF-8522-2227 GF-8532-2227 GF-8542-2227
1 - 20 GF-8520-2327 GF-8530-2327 GF-8540-2327 GF-8521-2327 GF-8531-2327 GF-8541-2327 GF-8522-2327 GF-8532-2327 GF-8542-2327
1 - 50 GF-8520-2427 GF-8530-2427 GF-8540-2427 GF-8521-2427 GF-8531-2427 GF-8541-2427 GF-8522-2427 GF-8532-2427 GF-8542-2427
10 - 200 GF-8520-2627 GF-8530-2627 GF-8540-2627 GF-8521-2627 GF-8531-2627 GF-8541-2627 GF-8522-2627 GF-8532-2627 GF-8542-2627
20 - 500 GF-8520-2727 GF-8530-2727 GF-8540-2727 GF-8521-2727 GF-8531-2727 GF-8541-2727 GF-8522-2727 GF-8532-2727 GF-8542-2727
150 - 1200 GF-8520-2827 GF-8530-2827 GF-8540-2827 GF-8521-2827 GF-8531-2827 GF-8541-2827 GF-8522-2827 GF-8532-2827 GF-8542-2827
FLOWM6ETER1S