油墨是为了在ＰＰ等硬质聚烯烃类材料上印刷而开发出来的挥发性干燥型的油墨。 推荐用途 经处理PP片材，未处理PP片材，经处理PE瓶等硬质聚烯烃类，以及金属涂装板等上的印刷。 (PP:是聚丙烯的简称，PE:是聚乙烯的简称) 特长 对聚烯烃类材质的附着性。 油墨皮膜强韧，耐磨耗性佳。 耐油性，耐酒精性与耐化学药品性。 耐光性，耐水性，耐湿性好。 PP油墨特性：免处理、耐磨达6级、耐刮达5级、耐酒精、白电油、溶济、抗酸、碱，曲折性好、好调色，耐候性佳，油墨细腻均匀好施工，划格子用3M胶子粘性能测试通过附着力强，低气味无毒油墨。 PP油墨用途：硬质PP、有处理之PE材质、如、文具夹、化状瓶、药瓶、商标、掉牌、溶器罐、头盔、汽车部件、电子制品配件、电器产品配件、特种行业的产品，等聚丙烯材质（PP）的印刷或喷涂工艺。 PP系列油墨 油墨特性：拥有和德国彩丽宝一样的颜色，主要用于PP、PE、BOPP等材料上，具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及耐磨擦之特点。 印刷：丝印移印均可。 表干及实干时间：表干时间自然挥发5-10分钟；实干时间在24小时以内。 稀释及清洗：SV3慢干开油水、UVK1（移印开油水）同时可使用718洗网水清洗。 测试方法（完全干燥后）： 1、3m胶纸粘在画有百格的油墨表面，45度角迅速拉起不脱油； 2、纯度99%的工业酒精，一千克砝码用棉布包住在油墨表面，以水平力来回拉200次无脱色； 3、耐磨：橡皮擦500g力水平来回擦500次。 使用方法： 1、使用前应充分搅拌，用后随时封闭； 2、搅拌时加开油水10-15%，稀释到印刷粘度； 3、网板塞网时可用洗网水清洗； 4、不得与其它类型油墨混合使用。 注意事项： 1、塑胶材料的外观相似，但可能会是不同的材料，客户需试印确定其符合要求后，再批量印刷； 2、在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可； 3、环境温度过高，将会影响油墨原有质量； 4、根据气候变化，请远离火源，阴暗环境下存放。 Ink characteristics: have and Germany Caili treasure the same color, is mainly used for PP, PE, BOPP and other materials, with a high color, high color, high covering power, alcohol resistant and wear resistance, high stability. Printing: silk screen printing can be. Table dry and work time: surface dry time natural volatile 5-10 minutes; work time within 24 hours. Dilution and cleaning: SV3 slow dry open water, UVK1(printing open water) also can use 718 washing network water cleaning. Test method (completely dry): 1, 3M adhesive tape sticky ink surface adhesion in painting,45 degree angle quickly pulled off the oil; 2, purity 99% of industrial alcohol, using cotton bag in the surface of the ink one kilogram weight to horizontal force and pull 200 times without decolorization; 3, wear: the eraser 500g force level wipe 500 times back and forth. Method of use: 1, before the use should be fully mixing, use at any time after the closure; 2, mixing an additional 10-15% in oil and water, diluted to printing viscosity; 3, mesh plug mesh can be used when washing network water cleaning; 4, shall not be mixed with other types of ink. The matters needing attention: 1, the plastic material of similar appearance, but may be of different materials, customers need to try to determine its requirements, and then bulk printing; 2, in the printing process, such as drawing or spread out,may be appropriate to add some slow dry paste can be; 3, the ambient temperature is too high, it will affect the quality of the original ink; 4, according to the climate change, please stay away from fire, stored in dark environment.